3 m Ballasted Terrace and Flat-Surface Stand \u2013 \u00d8 60 \u00d7 2 mm Sectional Mast for Satellite, Radio and Suitable Small Wind Generators<\/p>\n
The AS21020 is a heavy-duty ballasted mast stand designed for suitable terraces, flat roofs and other level installation surfaces.<\/p>\n
According to the available product data, the structure is manufactured from hot-dip galvanised steel and uses a 3 m sectional mast with an outside diameter of \u00d8 60 mm and a wall thickness of 2 mm.<\/p>\n
The mast can be tilted by up to approximately 2\u00b0 for minor alignment.<\/p>\n
The base is designed to accept 50 \u00d7 50 cm concrete slabs, which are not included.<\/p>\n
According to the basic product data, the frame is intended for four slabs. Additional product information states a minimum of four slabs and currently recommends 16 slabs. The actual ballast required must, however, be determined from the complete installation and local wind conditions.
\n3 m sectional mast<\/p>\n
Mast specifications:<\/p>\n
Height: 3000 mm<\/p>\n
Diameter: \u00d8 60 mm<\/p>\n
Wall thickness: 2 mm<\/p>\n
Design: sectional \/ plug-together mast system<\/p>\n
The sectional design makes transport and handling easier than with a single 3 m tube.
\nHot-dip galvanised steel<\/p>\n
The structure is manufactured from hot-dip galvanised steel according to the product data.<\/p>\n
This supports corrosion protection for permanent outdoor installation.
\nAdditional bracing<\/p>\n
According to the additional product information, the mast structure uses four additional support braces.<\/p>\n
These help stiffen the connection between the mast and base frame.
\nBallasting with 50 \u00d7 50 cm concrete slabs<\/p>\n
The base accepts concrete slabs measuring:<\/p>\n
50 \u00d7 50 cm<\/p>\n
The slabs are not included.<\/p>\n
The number of slabs alone does not define the stability of the system. Slab thickness and actual total ballast mass are also important.
\nBallast depends on the complete installation<\/p>\n
Required ballast depends on factors such as:<\/p>\n
mast height<\/p>\n
attached equipment<\/p>\n
wind area<\/p>\n
installation height<\/p>\n
building height<\/p>\n
local wind conditions<\/p>\n
position on a roof or terrace<\/p>\n
dynamic loads<\/p>\n
Mast adjustment up to approximately 2\u00b0<\/p>\n
The mast can be tilted by up to approximately 2\u00b0.<\/p>\n
This can assist with minor alignment and compensation for small deviations in the installation surface.
\nAnti-slip rubber feet<\/p>\n
Anti-slip rubber feet support stable contact with suitable surfaces and reduce direct metal-to-surface contact.<\/p>\n
They do not replace adequate ballast.
\nSatellite applications<\/p>\n
The AS21020 can be used as a support for suitable satellite antennas on:<\/p>\n
terraces<\/p>\n
suitable flat roofs<\/p>\n
other suitable level outdoor surfaces<\/p>\n
No specific maximum satellite dish diameter is stated in the available data.
\nRadio and communication applications<\/p>\n
Depending on the total mechanical load, the mast can also be used for suitable:<\/p>\n
DVB-T\/T2 antennas<\/p>\n
DAB\/DAB+ antennas<\/p>\n
FM antennas<\/p>\n
WLAN antennas<\/p>\n
directional radio antennas<\/p>\n
communication equipment<\/p>\n
Cameras and measuring equipment<\/p>\n
Suitable cameras, sensors, weather instruments and measuring equipment may also be mounted, provided weight and wind area are compatible with the mast system.
\nSuitable micro and mini wind generators<\/p>\n
According to the available product data, the stand is also intended for suitable micro and mini wind generators.<\/p>\n
Wind turbine installations create additional dynamic loads including:<\/p>\n
rotor forces<\/p>\n
vibration<\/p>\n
alternating wind loads<\/p>\n
torque<\/p>\n
cyclic mechanical stress<\/p>\n
The turbine must therefore be checked for compatibility with the \u00d8 60 mm mast and the complete stand.
\nFlat-roof installations<\/p>\n
When installed on a roof, particular attention must be paid to:<\/p>\n
permissible roof load<\/p>\n
total ballast mass<\/p>\n
point loads<\/p>\n
roof membrane protection<\/p>\n
drainage<\/p>\n
wind uplift<\/p>\n
roof edge zones<\/p>\n
Regular inspection<\/p>\n
For permanent outdoor installations, regularly inspect:<\/p>\n
mast connections<\/p>\n
support braces<\/p>\n
ballast<\/p>\n
mast alignment<\/p>\n
rubber feet<\/p>\n
mounted equipment<\/p>\n
Wind generator installations should additionally be checked for vibration-related loosening.
\nTechnical specifications<\/p>\n
Article reference: AS21020
\nArticle number: 21020
\nEAN: 4050822210206
\nProduct type: Ballasted terrace \/ flat-surface mast stand
\nMaterial: Steel
\nSurface: Hot-dip galvanised
\nMast: \u00d8 60 \u00d7 2 mm
\nMast height: 3000 mm
\nMast design: Sectional system
\nAdditional bracing: 4 braces according to additional product information
\nMast adjustment: Up to approx. 2\u00b0
\nConcrete slab size: 50 \u00d7 50 cm
\nBasic product specification: For 4 slabs
\nAdditional information: Minimum 4, currently 16 slabs recommended
\nConcrete slabs included: No
\nFeet: Anti-slip rubber feet
\nApplications: Suitable satellite, radio, camera, measuring and small wind-power systems
\nPackage contents<\/p>\n
1 \u00d7 AS21020 ballasted mast stand
\n1 \u00d7 3 m \u00d8 60 \u00d7 2 mm sectional mast
\nSupport braces according to product configuration
\nAnti-slip rubber feet according to product configuration<\/p>\n
Concrete slabs, antennas, wind generator, cables and additional installation equipment are not included.<\/p>","protected":false},"excerpt":{"rendered":"
3 m Ballasted Terrace and Flat-Surface Stand \u2013 \u00d8 60 \u00d7 2 mm Sectional Mast for Satellite, Radio and Suitable Small Wind Generators The AS21020 is a heavy-duty ballasted mast stand designed for suitable terraces, flat roofs and other level installation surfaces. According to the available product data, the structure is manufactured from hot-dip galvanised […]<\/p>\n","protected":false},"featured_media":682713,"template":"","meta":{"ep_exclude_from_search":false},"product_cat":[226],"product_tag":[],"class_list":{"0":"post-682711","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-balkon-gelaender","7":"product_shipping_class-sperrgut-einfacher-zuschlag","9":"first","10":"instock","11":"taxable","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/technikrat.de\/en\/wp-json\/wp\/v2\/product\/682711"}],"collection":[{"href":"https:\/\/technikrat.de\/en\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/technikrat.de\/en\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/technikrat.de\/en\/wp-json\/wp\/v2\/media\/682713"}],"wp:attachment":[{"href":"https:\/\/technikrat.de\/en\/wp-json\/wp\/v2\/media?parent=682711"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/technikrat.de\/en\/wp-json\/wp\/v2\/product_cat?post=682711"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/technikrat.de\/en\/wp-json\/wp\/v2\/product_tag?post=682711"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}